Hot glue fix dents? #Shorts

تم نشره في 2021/04/ 1
Merch: fanparel.com/collections/dylan-ayres
Tik Tok: Dylandoestiktok1
Instagram: dylanayrestiktok

تعليقات

  • You have to let it harden

  • He did it wrong haha. You have to get the sticks pretty melted and then allow them time to cool and dry then pull. It does work pretty well actually

  • Try holding the gurl there so it can dry a bit THEN pull it off

  • It works, i tried this on my car a while back but it is time consuming and the glue has to be cool to the touch.

  • Only works on cheap throw away commuter cars w thin boby panels

  • Rich people I tell ya. Lol

  • Dude didn't do it right

  • His problem was that he followed 5 minute crafts

  • You should use hot water treatment and spray paint, it's the safest method.

  • Moral of the story : dont trust 5 minute craft

  • Maybe your putted to much Fire on the glue

  • Try hot water and a plunger

  • You didn't do it right.

  • 5 minute crafts videos are jyst clickbait and total bullshit.

  • Bruh "THIS IS INDEED, CAP..." Lol

  • Buat rosak kereta je

  • Let it dry

  • I made a dent with my rubber band ball. Priceless. That made me laugh.

  • You gotta let it fully dry- I mean it prolly won’t work either way but-

  • Use a lot more glue sticks and let it dry

  • Did u let it cool?

  • You did not let it dry

  • plunger will work but it will rip off the paint

  • Let it dry first and see what happens

  • Stupid

  • ก็มันยังไม่แห้งอะไอ่เวร

  • You have to wait until the glue dries enough

  • Big brain over here not letting the glue cool down at all lmfao

  • He didn't snap it back and pulled it slowly...

  • You know you have to let it dry

  • You have to hold the glue sticks for longer so they stick good

  • I did it and it does work it just that you need to leave in the car for like 5 minutes and then you pull it out

  • 🤣🤣🤣CAP🤣🤣🤣

  • It might be the glue

  • I think you were supposed to wait for it to dry

  • Dude just give the car to me. Wasting a perfectly good car

  • Let the glue cool down first

  • Btw there is people inside the car push the door where the damage so it's fix btw don't try any hack it's ruined you life

  • He didn’t wait near long enough

  • wait for dry, gblok

  • Gotta heat the dent up with boiling water genius

  • You gotta let it stick for like- 5-8 minutes or so :)

  • Did you leave it on it long enough

  • Soooo AR-one has tic tok shit now wtffff

  • Its because you have a car with a metal exterior, the one that worked is made out of fiber glass or plastic

  • Use toilet plunger and hot water it works

  • 😂

  • LOOK UP, PDR.........

  • he just fricked up his car.

  • Didn’t do it long enough

  • Man this lifehack sucks even if it would work, it leaves traces of glue on the car, which just simply fucks over the paint and makes the repair costs more. Often times if the dent is in a part where the other side of the metal is visible (say by the fenders) a hammer is all you need.

  • You’re supposed to let it cool down 😫

  • LET THE GLUE DRY MY GUY

  • Is your mother the sister of your father ? because it's can explain a lot of thing 🧐

  • Maybe let it properly stick

  • 5 Minute Crafts : Let it cool! Dylan : **Doesn't let it cool** Also Dylan : *This is cap*

  • Pulled the glue before I could actually stick to the mettle

  • Pulled the glue before I could actually stick to the mettle

  • This is why Tik tok really grinds my gears

  • Nigga let the glue setttle and cool

  • U have to leave it and let it dry

  • Just use a fucking plunger.

  • When u know u failed the second time but u still try to stick em back

  • Your supposed to wait a bit before pulling

  • Leave it on for ponger

  • Ur trying that on american steel That mazda or whatever in the video is probably dent resistant plastic which is much easier to pop back out. Plus it was on a big flat panel. Most of your dents were on or near body lines

  • Scuff the paint first

  • It appears the difference is the video you are looking at let his dry before pulling... Not to be rude, but pretty much a common sense thing actually.

  • IT DEpends on the type of hot glue ur using

  • Lol

  • let it cool down first

  • Don’t do that wait for the hot glue to dry on the car then after that you pull it out and then you can cut off the hot glue please try to go

  • You did wrong, u had to warm the car instead

  • Sycopath

  • Hmm its almost like glue needs to cool down

  • Was their dent on plastic and yours on metal?

  • I’m mean it’s 5 minute crafts did you expect it to work

  • Yeah, I never would've thought that'd work & I feel bad for your SUV. I'll take care of the SUV; how about that? He'll be happy at his new home with me.

  • I didn't expect that it would work anyways, this is 5 Minute Crafts we r talking about for God's sake

  • Let it stay up there for a few secs and let it cool

  • dont really care mate

  • You have to let the glue dry

  • Maybe he waited for the glue to actually stick

  • You gotta let the glue dry my dude

  • Bro it was 5 minutes craft what were you gonna expect?

  • Bro my mum was going to try this NOW I CAN PROVE HER WRONG

  • Prolly didn’t let it cool

  • Your supposed to let it melt onto the car

  • Just my guess, probably have to wait till it’s a little warmer out

  • Lol dude let the fkn glue dry you impatient imp.

  • You need to let the glue dry

  • You do not make good. Look at Ad Buster Chanel.

  • Let it cool

  • Put boiling water on it then use a plunger to pull it out

  • Let’s yank the glue while still hot! Let’s not let it dry! Haha told you it was fake

  • Idiot kid. Wait for the glue to cool down and dont just pull,

  • You have to wait for it to cool down

  • I'd use a plunger i heard it helps quite a bit

  • I’m ducking stupid asf, but I bet you I would have found a way to get it undented

  • Get a plunger and hot water it should work it workt by me!